Biocheck Allweather Masonry Paint

Out of stock
Only %1 left
SKU
Biocheck Allweather Masonry Paint
BIOCHECK ALLWEATHER is a Pliolite® resin-based masonry paint developed to give long-term protection to masonry surfaces undergoing redecoration. read more

Enquire about this product

Fast delivery available
Tested & verified products
Over 50 years experience

Need some advice? Please call us on 01372 743 334

We’re open 9:00am - 5:00pm Mon-Fri

External decoration is time consuming and costly.  It is not uncommon for redecorated properties – to the total dismay of the homeowner or specifier – to show signs of ageing and weathering long before completing their anticipated life span.  There are many factors that contribute to the early breakdown of coatings, two of the most common are that the substrate was not correctly prepared prior to redecoration and inappropriate materials were used to treat external growths of moss, lichen and algae.

Over the past 20 years the problem of external growths has increased dramatically.  As a result of the reduction in air pollution and carbon emissions there has been a huge increase in airborne spores of moss, lichen and algae and unless treated correctly will subsequently reduce the life expectancy of normal masonry paints.  There are 100’s of varieties of algae and external growths which attack masonry surfaces, predominantly green or black, however, in certain areas of the UK there is a red algae called Trentepohlia aurea which is particularly virulent.

BIOCHECK ALLWEATHER Pliolite® resin-based masonry paint has been specifically formulated incorporating active biocides to provide long-term protection against these damaging and disfiguring growths.  It is a superior masonry coating which provides protection against wind, driving rain, sun, temperature extremes and atmospheric pollution whilst at the same time retaining its decorative appearance.

BIOCHECK ALLWEATHER provides excellent adhesion to the building substrate and will penetrate and adhere to even the most difficult masonry surface without the need for a separate primer.  The coating acts as a total barrier to rain, however, is micro-porous and will allow moisture in the wall to pass through the paint film without blistering.  BIOCHECK ALLWEATHER is formulated in such a way that it is ”self-cleaning”.  A few microns of the surface are regularly removed by rain which removes any retrained dirt but without affecting the life expectancy of the coating.  BIOCHECK ALLWEATHER is an all-weather coating which allows application to continue in conditions and at the time of year when it would not be possible to proceed with traditional water-based masonry paints. 

Benefits

  • UP TO 15 YEAR LIFE EXPECTANCY
  • RESISTANT TO ALGAE GROWTH
  • BREATHABLE COATING
  • SELF-CLEANING
  • EXCELLENT ADHESION
  • ALKALI RESISTANT
  • APPLICATION AT LOW TEMPERATURES
  • RESISTANT TO RAIN AFTER 20 MINUTES
  • APPROVED BY THE HEALTH AND SAFETY EXECUTIVE UNDER C.O.P.R 1986 (as amended)

 

APPLICATION INSTRUCTIONS

Surface preparation

1. Ensure all surfaces are sound, dry, clean and free from dirt, oil, grease or other contaminates. Treat moss, lichen and algae growth with LICHENITE in accordance with instructions. For heavy contaminations use high pressure water jetting to remove growths. Leave 24 hours before proceeding.

2. Cracked and damaged surfaces to be repaired with suitable exterior grade proprietary filler.

3. Stir BIOCHECK ALLWEATHER Pliolite® resin-based masonry paint thoroughly before use. Apply liberally by brush, roller, conventional or airless spray.

4. Porous and Powdery Surfaces – Brush apply first coat thinned with up to 15% or which spirit per 5 litres by volume. Follow with one or two full coats of BIOCHECK ALLWEATHER Pliolite® resin-based masonry paint as required to obtain full obliteration.

5. Non porous, sound surfaces – Brush, roller, convention or airless spray apply two coats of BIOCHECK ALLWEATHER Pliolite® resin-based masonry paint undiluted.

Spray: Can be thinned with up to 5% of which spirit by volume per 5 litres of paint.

Covering capacity

Dependent upon substrate profile and suction, typically:

Porous/textured surfaces: 3-4²m per litre
Non-porous surfaces: 6-8²m per litre

Drying time: touch dry in 1 hour, recoat 16 hours.

Colours: White, Magnolia, Cream, Parchment, Maltese Stone, Dewdrop,
Peanut Butter, Summer Blue, Ivory, Terracotta and Seagull.
Full BS Range available on batch size order.

Cleaning: Clean brushes, rollers and spray equipment immediately after use with white spirit.

Availability: Supplied in 5 litre containers.

Storage: Ensure the container is stored upright and secure at all times.
Protect from frost and extremes of temperature.
Keep out of direct sunlight.

Health and Safety

All MGC Mould Treatments, Fungicidal Paint/Paste Additives and Fungicidal Paints and Coatings are Approved by the Health and Safety Exective Under C.O.P.R. 1986 (As Amended).

Would you like to find out more technical information?